Video

Dude, your video was very helpful. I’m going to the same situation with my 2014. Thank you for the vids

Did you buy the ones off Amazon? I did and they don’t twist properly into the holes. Have to send them back.

Where did you purchase the parts for the windows?

Will be doing mine soon, I'm going to replace the tranny alos. 2015 silverado bought new and serviced. 150,000 miles

Working on an 02 base here. Looking to everything you did here minus the camber arms. Any suggestions after having this installed? Also is this the 22mm or 24mm sway bar form progress?

I know this video is several years old but thank you for taking the time to make this. After you completed installing the expansion valve did you recharge the system or did you have someone else do this? I am trying to find out how much PAG oil I need to add if we are only changing the expansion valve and nothing else? Thanks in advance for any help you can offer.

A Hero that saved the day ❤🎉 thanks man!!!!

do u need special bolts? For the lower control arms

What was ur trans diong Was it whining slipping jerking. Bc I’m having these issues with my 16 Silverado

can you use prestone 50/50 mix or is the added cost for engine ice worth it?

Great video. Now I need to know how to do the shifter lights and cruise control area.

great video. what’s the torque on the bolts?

Has anyone tried putting a heat shield around the exhaust pipe underneath the tranny pan to make it run cooler?

Do you recommend this mount I got has ports but it didn’t come with the front I’m not running crazy power just factory so should I get this or the hardrace factory looking one?

How has it held up? Appreciate the feedback. Nice vid

Bout to try this soon.

dude recorded this with no light

How did you determine that the water was coming from that ?

nice job man - keep it up

1/2 inch socket !!!! Those take 13mm, vehicle is metric !!! You should drain any compressor oil into a container so you can measure it - like measure how much - if any - remained in the old compressor. Yes, you can add the oil to the compressor low side port, then when you get that mounted, manually rotate the compressor drive plate through like 10 revolutions using a socket and ratchet.

Hey now! Good stuff brother I was going to take it in and not deal with but after this, 18 pack of some ultra, time and Led Zeppelin and I’m going in… thanks man! Expansion is exactly like u said like a nozzle, helps drop the pressure for the low side as it goes into evaporator… Congratulations on new baby!!

great video man

I’m looking for a gmt800 kit. I’d imagine this would work but not 100%

Thank you for the video. Wish I would have watched it before I did the work

just got my first dc5. this video helped my out a lot. thanks man

I just replaced all my components on a 2015 with a locked up compressor. You need to flush your evaporater also I used 3 quarts until I got clean metal free fluid. Also condenser and the 2 hoses with mufflers. If you don't do all this the contamination will destroy your new compressor

Thanks for the video 👍 worked perfectly

Why sway bar

Thanks for the video.

I couldn't find a good video so thank you for your in depth video. Much appreciated!

So did this help your issue? Thank you! im going to change mine as its brown no issues yet tho

Your camera is aiming somewhere else.

Did you evacuate before taking the expansion valve off?

If ya don’t mind me asking I’m taking my spare k20z1 head to shop to have super tech valve job done . About a round about of how much they charged to do yours ??

I installed a fuel controller and didn’t like the results I was getting, I took it off but my bike is still set on the power commander settings What can I do?

What you found on the magnet is completely NORMAL. As long as you don’t have chunks or like needle bearings then you’re completely fine.

Dang… who was your parts plug on those

Is the breather filter for use only with the K&N intake cause my Fujita SRI has a port and hose there that attached to the intake. 06 Type S

At 5:30 I used 3 pieces of 2x4 and made a H they ran the length of the pan on either side with the wider side along the trans pan then screw the 3rd board across the middle of the pan. The 3.5" is about perfect to keep anything from touching the pan. Then the jack goes on the 3rd 2x4.

Very good! Like your candid presentation!

At 5:30 reach in and turn tq converter with finger make sure it's not jammed.

3 snowdrift videos in 1 month let’s go

2024. This helpped me. The parts number was excellent! You are doing the world a favor, you just didn't know. One bulb went out on me, I plan to replace all of them might as well.

I also need civic parts

I did mine the other day and get the pan off my dad got got under the truck with me he had a big screwdriver and he bent that bracket back that holds the linkage to the gear shifter on side the transmission

Gahhhhh finally

This guy is an idiot! Sepreme suspensions as well as every other company out there that sells these kits, clearly show that the soacers go between the mounts and the frame. Do not do this the way he shows in the video. Doing this can cause catastrophic failure due to the spacers not having any cushion. Which would cause the spacers to either break or the bolts to break and your diff falling out. Dont be like this guy. Read your instructions thoroughly and watch the videos on the manufacturers website. Really hope theres not very many people doing this. If you did, fix it asap.

windshield screws are dope , love it

Thanks man I appreciate you simplifying it

I haven’t fucked mine up yet but thanks for the video, 6 years later and giving me helpful insight before I go in there.