![Pink Caddy Garage](/img/default-banner.jpg)
- 62
- 1 518 275
Pink Caddy Garage
United States
Registrace 3. 09. 2020
Mitsubishi L300 Delica Oil Change - Turbo Diesel
The first in a series of several videos changing the various fluids on this 1992 Mitsubishi L300 Delica Star Wagon Turbo-D Super Exceed (!). More and more of these are trickling into the States since they are past the age where EPA and other regulations apply. Follow along!
zhlédnutí: 309
Video
How to Inspect & Change Ford Super Duty/Excursion U-Joints
zhlédnutí 2,7KPřed 10 měsíci
In this video we go through the process of inspecting and replacing the universal joints on a Ford Excursion ( also applies to Super Duty pickups). The process to lubricate the slip yoke is also provided since this is easy to do while the driveshaft is out. This was done because I was experiencing a slight hum/vibration when accelerating and replacing the rear u-joint cured the issue.
How To Replace Kia Sorento Rear Brake Pads & Rotors
zhlédnutí 31KPřed rokem
A short video showing how to replace the rear brake rotors and pads on a 2013 Kia Sorento, same for years 2011-2014, probably more. It only takes about 15 minutes per side. Here are the Amazon affiliate links for parts and tools: Rear Brake Rotors and Pads amzn.to/3fNuoOV Brakleen amzn.to/3gIiyWs Floor Jack w/ Two Jack Stands Included amzn.to/3N5qVrm Torque Wrench amzn.to/3TT19J5 Impact Wrench ...
How To Replace Kia Sorento Windshield Wipers
zhlédnutí 23KPřed rokem
If you've never replaced your vehicles windshield wiper blades yourself, here's a short video showing how it's done. I used my 2013 Kia Sorento in this video (remember, there are 2 different-sized blades on this vehicle), but the same procedure applies to many different makes and models. Here are the Amazon affiliate links for both blades: Rain-X 24" Right Blade amzn.to/3cUYcYu Rain-X 20" Left ...
How to Replace a Broken Kia Door Handle
zhlédnutí 111KPřed 2 lety
In this video I'll replace a broken Kia door handle on my 2013 Sorento. This applies to all Kia Sorento models between 2011-2015 specifically, but it may work on other years/models as well. Total cost to replace this handle was around $14.00 at the time of filming and it took about 10 minutes. I believe the only tools used were a Philips screwdriver and a pair of pliers. Here are the Amazon aff...
Ford NAA - How to Change Oil & Filter
zhlédnutí 2,1KPřed 2 lety
I'm getting this 1954 Ford NAA tractor ready to put back in to service after it sat in the weeds for over 10 years. I'll be changing all the fluids beforehand, this video covers the engine oil and filter replacement.
How To Replace a Ford NAA Fuel Tank
zhlédnutí 6KPřed 2 lety
I just got this 1954 Ford NAA tractor running and the fuel tank has way too much rust and debris clogging up the sediment bowl. So, I ordered a new tank and this video outlines the replacement process.
How to Replace Mercedes GLS Rear Brakes
zhlédnutí 18KPřed 2 lety
In this video we show to replace Mercedes GLS rear brakes. Pads and rotors were replaced for about $145 plus shipping. Specifically, this vehicle is a 2017 Mercedes GLS450. UPDATE: Prices are up some, as usual, but here are tools and products for both front and rear brake kits (original equipment level): Rear pads/rotors: amzn.to/3ej8Mc7 Front pads/rotors: amzn.to/3ej8Mc7 Brakleen amzn.to/3gIiy...
Cadillac SRX V8 Spark Plug Replacement
zhlédnutí 6KPřed 2 lety
This is an video about Cadillac SRX V8 spark plug replacement. This applies to Cadillac SRX years 2004 - 2009. Most shops want over $300 for this job. You can do it yourself for under $100 and about an hour's worth of your time. Here are some links to tools and products: AC Delco Rapidfire Platinum spark plugs: amzn.to/3TKcSKU Spark Plug Boot Pliers amzn.to/3SBExLW Spark Plug Socket with Extens...
How to Replace Mercedes GLS450 Spark Plugs
zhlédnutí 25KPřed 2 lety
How to Replace Mercedes GLS450 Spark Plugs - This is a detailed video showing how to replace Mercedes GLS450 spark plugs, including how to remove all the pieces to actually get to the spark plugs. Toward the conclusion, there is an overview of the tools needs to do this job. I ordered my plugs from rockauto.com, as of this writing they are about $62.00 plus shipping. If you prefer Amazon, here ...
How to Install Boots on Plug Wires
zhlédnutí 15KPřed 3 lety
If you're trying to install boots on plug wires (cut-to-fit style) and are having a tough time, this video shows how I (finally) got mine installed.
How To Remove Mercedes GLS Engine Cover
zhlédnutí 6KPřed 3 lety
In this video you can see how to properly remove the engine cover on a Mercedes GLS 450. You can avoid cracking or breaking the attaching pins by following the process in this video.
How to Replace a Freeze Plug
zhlédnutí 29KPřed 3 lety
This video will show how to replace a freeze plug. Freeze plugs, core plugs or casting plugs...whatever you call them, they will eventually need replacing due to corrosion or leaking. Replacement can be done with the engine in the vehicle, but it's obviously a much simpler job to do if the engine is out. Although these plugs were in good shape, I figured it was good preventative maintenance to ...
How to Clean Carbon Off Pistons
zhlédnutí 51KPřed 3 lety
If you have your engine out it is an excellent time to clean the carbon off the pistons and combustion area. Using a mix of acetone and transmission fluid, you can get those pistons looking practically new again!
GMC Sierra 4x4 Restoration - Needs Everything!
zhlédnutí 798Před 3 lety
This is the intro to our gmc sierra 4x4 restoration project. It'a 1984 GMC High SIerra 4x4 shortbed. This truck needs it all, but at least it appears to be a solid foundation!
How to Replace a Kia Sorento Brake Light Bulb
zhlédnutí 56KPřed 3 lety
How to Replace a Kia Sorento Brake Light Bulb
Square Body Truck Front Brake Replacement
zhlédnutí 24KPřed 3 lety
Square Body Truck Front Brake Replacement
How To Replace Mercedes GLS450 Wiper Blades
zhlédnutí 21KPřed 3 lety
How To Replace Mercedes GLS450 Wiper Blades
How to Check Your Vehicle's Steering and Suspension
zhlédnutí 2,8KPřed 3 lety
How to Check Your Vehicle's Steering and Suspension
Cadillac ELR Oil Change At Home (and Chevy Volt)
zhlédnutí 2,1KPřed 3 lety
Cadillac ELR Oil Change At Home (and Chevy Volt)
Lost the C10 Silverado in a Pickup Fire in 1 Day!
zhlédnutí 697Před 3 lety
Lost the C10 Silverado in a Pickup Fire in 1 Day!
C10 Pickup Paint Resurrection "How To Video"
zhlédnutí 248Před 3 lety
C10 Pickup Paint Resurrection "How To Video"
Square Body Project Truck Anniversary Present
zhlédnutí 126Před 3 lety
Square Body Project Truck Anniversary Present
Check out this portable tire inflator!
zhlédnutí 196Před 3 lety
Check out this portable tire inflator!
You have no idea how much I appreciate this video & your superior knowledge. We had to make the modified socket for my 97 Chevy Tahoe & it worked like a charm when all else had failed. Thank you thank you thank you!!
Yes Girl Power!! I ordered my new cap, I'll update when I get done. Thanks for sharing 🤍
This is extremely helpful! Now I may actually be able to get my boat out on the water. 😂
Excellent video thanks!!
From who did you purchase your fuel line and sediment bowl? I have the exact same tractor with the same trouble: Runs for awhile then the bowl or cab inlet screen clogs and the tractor stops. Than you!
If my memory serves me correctly, believe I bought everything at Walt’s Tractor Parts. Just Google it it should come up right away.
@@pinkcaddygarage267 Thank you. I really appreciate it.
Thank you for walking us thru this. Nice ride Sir.
Thanks.
Open the bleed screw, don't take the cap off the brake fluid reservoir. You don't want the crap in the caliber moving back into the system that's how u get an abs failure
Thanks!
I have to reset mine every day to charge. I have replaced the sensor and topped off the antifreeze, which was not really low. The heater water pump needs to be replaced again #3, all with less than 55000 miles. Otherwise it has been a good car.
This is an excellent video. Extremely helpful. Well done Sir.
Very helpful video! I purchased the same filters and noticed that the two cabin filters you put in are actually upside down, if you look the arrow indicating the airflow points toward the blue side. Thanks!
You are correct! Even though they seemed to work fine, on the next filter change I went in through the glovebox side… probably should make another video.
Thanks my friend
My Chevy Volt is charging again! I can't thank you enough.
I need that right now
Easy to make.
where did you get the stickers from?
They were already installed on the new part from the dealer.
IS THIS THE SAME FOR 2009 KIA SPORTAGE?
Not sure.
No metal on paint. yall are killin me. lol
Is this supposed to be done directly after being serviced
Correct
Thanks for sharing. Happened to me today. Such an easy fix. 2015 Sorrento owner 👍🏿 $9.99 part from Amazon
Tried it on a 2017 XTS, so far so good! Thanks!
In the rear of the engine can the plugs fall in and not be able to get out?
Generally, the transmission is removed to access the o es at the rear, so not an issue.
The tool will work but you have to know how to use it
THANK YOU!!!! I sent your video to my mechanic and in 1 hour, my 2013 145,000 mile Volt was back charging. I love your site and love my Volt. Thank you again.
I’m glad to hear that it helped keep your Volt on the road!
Thank you. Very comprehensive and foolproof video. 😊
Glad to help!
Thank you so much for making this video. I ended up pulling the tranny pan and sure enough the plunger wasn’t going in all the way. I thought I had the kick down adjusted correctly up top but I didn’t. The Camaro downshifts like a champ now. I’m actually enjoying my new engine and tranny.
Glad it worked, it is such a beating when the car won’t downshift correctly.
Great video. I just finally bought a 2016 ELR after having first seen one at the Chicago Auto Show in 2014. Ibhave a 2013 Volt.
Very cool!
My driver side door in the back this just happened to It like totally just fell apart in my hand. I'll have to give this a try and hopefully it works
Thank you sir I’ll try this tomorrow you saved me a lot of time and money
Awesome video. Saved me $400 and a DAY at the dealership. I did this in FIVE MINUTES, only because I forgot to put the gasket on the first time 😅. Shame on you, Kia!
Im in love 😻
Would this work for a 2005 Kia Sportage? Thank you
I’m not sure if the design is the same or not.
Very good video👍. Now i can fix my gearbox😀. Thanks brother👍
Thanks for your help! My husband has been tearing his hair out over this process!
Fantastic video! Every time I buy a NEW motorcycle I have been faced with the same problem of an oil filter, factory installed by KING KONG, which is very frustrating for sure. I do ALL of my own maintenance on all of my vehicles and have a full size, 4 post Hydraulic lift that makes things much easier. I also must have 20 oil filter wrenches and sometimes must use a large pair of 'Channel lock' plyers to do the job. Funny thing is, is that the 'Owner's manual's,' always warn against over tightening all connectors and especially the oil filters!
The factory guys don’t read the manuals! 😂
Great Video to help with my car door handle. It only took about 15 minutes at most and saved us over $200.00. Thank you
Thank you. You are the cool uncle. My first oil change by myself and This happened to me yesterday and I've been going ape crazy with this.
Seems to happen to a lot of people
That grease seal trick was super nifty.
Great video..easy to understand.
Thanks for the video! I'm trying to do my transmission fluid soon. Do you guys have a 5 speed or automatic?
Automatic, editing that video now.
Great review Elvis. I have a 2012 Volt that we really love. I would love to have something like this. Thanks for taking the time to produce this.
How can i fix my back passenger door handle? It doesnt have the black rubber circle thing
I’m not sure which part you were referring to
This is the exact video I needed. My new Kubota tractor has a factory installed oil filter fused onto the engine block. I tried a few things like the wrench cup before my old faithful and put a screwdriver through the filter shell. The screwdriver failed and started to rip the shell so I upgraded to a spud wrench for more leverage. As expected it tore the shell apart. So I removed the shell to clear away the jagged metal and now have a fused steel piece stuck to my engine block. Seeing this video I'm going to hit my garage tomorrow and try your trick. I truely hope it works for me since the alternative is take it in to the dealership at a shop rate of $179/hr.
I have a Kubota L3301, but so far it is only been dealer service so I haven’t run into that yet
2 years later, i needed this!! so glad i did research before taking it to a shop, thanks!!
Thank you. Good movie, but why not to use gloves?
Probably should
Thank you.
What about using an air hammer to "kiss" it gently?
Didn’t have one handy, but that might have worked
THANK YOU
Good job !! Thanks for the info. Tired of paying $260 at dealer.
Exactly what I needed to know - Explained clearly and quickly. Thank you.
I watched your video before I changed all mine this helped took bout 3days I have a 63 but the same set up but the Aarm bushings are definite on some n my kit had wrong ones but company overnight right onse no charge n think the wrong ones may work for Aarm in rear end...thanks