Video

Supper Time

what kind of snake is that?

His little cheek flaps were on beat

Tommy!

That is a rattle snake hybrid it was born with no rattle, rare but it happens

DO NOT BUY MADE IN CHINA!!!!! After a year parts are falling off due to not tightened right at the factory. JD uses Kubota tranny now. Height limiter on the 60" belly mower will wear out due to cheap extruded aluminum. My 2005 JD 2210 was built MUCH better and lasted 18 years. This one is a little over a year old and falling apart. JD does NOT care and will not warranty anything past 1 year.

Incredible! I gained so much knowledge from this video. It's fascinating to see the process of managing such huge logs. The quality of the video is excellent. I can't wait to see more of your content. Keep producing such high-quality content!

😂😂😂😂

Hi, Nice explanation. A big consideration is the timber and the 'set' on the blade. Assuming the blade is sharp, Green wood tends to 'tear' slightly some timbers Poplar, Willow etc are very soft and do leave a lot of fibres. Blades tend to be made to cope with 'anything' so will have 'maximum set' dry timber cuts with far less tendency to 'tear' as it is 'harder' so a blade with reduces set will cut well without binding. Look at a 'commercial' band mill' the blade is not 1" wide more like 6" to 12" so the cut stabilises the blade whilst the '1" blade is not guided so well so will wander particularly is the feed is too great, folks tend to forget the cutting rate is dependent on several factors, one very important one is the volume of the gullet...when it is full of sawdust it holds the blade off the cutting face, until it can empty, so a wide log will cut much slower as the gullets limit the cut rate, so you need to 'feel' the resistance to the feed to stop 'overfeed'. Lastly consider the amount of wood you are removing, a large set means you are removing a lot of timber, that takes energy, makes more sawdust, and slows the cut rate ( feet/min)

Change the oil take the loader off more room to work on it... or use the loader as a jack...hmm loader still on it

I’m a sharpener in East Tennessee

good video you have lots of work a head. take care, be safe and well.

Hey good fucking job looks great

Enjoyed the hike and the views it presented ... thanks Thomas .

Can I get the link for it

If this thing is really $60.000, that is ridiculously way over priced

got the actuator - forgot the gasket... wonder if I can use the original...? or if any auto part store has it?

Awesome snakes. Technically venomous but completely harmless to mamals. They're one of the snakes my 5 year old can safely handle before releasing.

REDNECK SNAKE! I like it

This is the best video I've seen for identifying these trees by walking through the woods. Thank you so much!

Is that driveway as steep as it looks on video?

W job bro

Cool great work 👍 💪

He needs to investigate the many specialty wood users mentioned in the comments. Other sawyers watching this video should also take note of how to upgrade "waste" for big profit.

This worked great thank you for video and the recommendation of putting truck on a slope that worked awesome the OEM part they quoted me 558 I picked one up off Amazon for 91

Hi Thomas, My 2520 has 130 hrs. My blade just started jumping off the wheel now as we speak, I was told that the wheel "BELT" normally requires replacement around 150-200 hrs. How often do you change yours ? It appears a bit too soon to me but what do I know. This mill has done me well with all the construction projects I have so cant complain at all. More project to come

behind walls and under floors you can use paint mixed with seven dust that will keep the bug away.

Any suggestions for repair my front bumper

Can you make video about how to fix your sawmill going up words as you cut

Knew there would be some EPIC figurals in that log!

It's a nice mill but I don't think that he has inspected and/or watched a Mahoe Supermill.

I was wondering if you check back to see if anyone had questions. I have a joystick that is messed up. Just wondering, where to get the parts and if I look it up what do I ask for? If you coukd put the answer to these question to this comment, I'll be checking back. Thanks.

My 1025R is an awesome workhorse. I’m sure I stress it well beyond it’s specs. I also use it to haul logs out of the bush many 20 inch plus and it’s small enough to get into tight spaces I have almost 700 hours and only significant maintenance has been a battery change. Works great on my 40 acres

Love the strict safety code. No hard hats, no heavy work gloves, no eye protection no steel tipped work boots. They probably have a iron clad work disability policy. Yep when a worker gets a arm cut off they give him a cup to beg for money.

take the sliding doors off the tracks. I do it all the time to get big items in n out

Check with your neighbors. I bet someone has a bottle of Chlordane. It'll kill bugs for years if oil based

Awesome job, it looks like you're having a lot of fun. Make sure you treat the ground for those termites.

Not having to deal with building codes can be a blessing or a curse. One can only hope that all of the termites have been found and repaired.

Im so inspired by you. You keep getting it done Thomas. Say hi to everyone for me.

good effort, plan plan plan, easy romove whole slider to get old big shower out, sell ur dads nice saw, this great family coming togehter most what ilike to see, go family team,

Ce n’est pas si simple sur un ecodiesel

I wouldn''t keep the old toilet, the new Kohlers are so much better and almost impossible to stop up.

Common Sense would tell you to use fencing with smaller openings. Duh

WOOF!

Holy f@#$! 😮

I've also seen that on cedar that I've milled. Cool looking. Cedar is kind of brittle, especially nailing into end grain. I usually pre-drill cedar.

Congratulations on your move home. Say hi to everyone for me

Beautiful place.

Our local Napa can make us up hydraulic hoses. It’s so nice to be able to get a new hose made up the same day

i hope you fire whoevers doing the plumbing because they dont know wtf there doing