![Marc Frank](/img/default-banner.jpg)
- 26
- 2 342
Marc Frank
Registrace 10. 07. 2018
6" DC, 4S 2200mAh, 2207 1900kv, testing an nd16 filter, no locked shutter speed
6" DC, 4S 2200mAh, 2207 1900kv, testing an nd16 filter, no locked shutter speed
zhlédnutí: 11
Video
6" DC, 2207 1950kv, GF 6x3x3, 4S 2200mAh
zhlédnutí 33Před měsícem
6" DC, 2207 1950kv, GF 6x3x3, 4S 2200mAh
this is why 3d printers need input shaping
zhlédnutí 21Před rokem
printing at 60mm/s with the Mingda Magican Pro when the movent of the bed changes, oszillations can very clearly be seen this is what causes ghosting on prints and the motors to skip steps when printing speeds are increased
DJI Goggles HDMI In - Side by Side - DRL Sim
zhlédnutí 128Před rokem
using an HDMI2AV converter added latency is noticeable
forrest flight #2
zhlédnutí 45Před 2 lety
422g auw, 2306 1950kv, 4s 1300mAh, gf51466, aio fc, vista, dji cam, custom frame dji fpv in high quality mode without focus mode
forrest flight
zhlédnutí 42Před 2 lety
422g auw, 2306 1950kv, 4s 1300mAh, gf51466, aio fc, vista, dji cam, custom frame
DJIG0047 - "long" range and chasing crows
zhlédnutí 39Před 2 lety
DJIG0047 - "long" range and chasing crows
electric glider 1st flight, flexible tail boom crash and 3rd flight
zhlédnutí 175Před 4 lety
electric glider 1st flight, flexible tail boom crash and 3rd flight
you've got a perfect spot to rip!
thanks :) it is pretty cool
Top
When a maiden video is only 11 seconds long it's usually not a good thing. Hope it survived and flew again!
It did survive and flew again :) But I broke the tail on the next flight
@@marc_frank Well at least it flew once!
@@mikesrcgarage 😁
Nice demonstration!
Thank you! Cheers
Wisel Looks Great! I great bird.
here it's covered with doculam i put fiberglass on it now, much stiffer and a kevlar hinge
Ahhh. How sad! It's a beautiful plane and I hope to build one once the 3D printer that I ordered arrives. Looks like you might have been a bit nose heavy. It looked like there was plenty of wind and the cliff was vertical. It was odd to not see it have any lift at all. It's hard to test the CG on these planes without a few crashes. Unfortunately, 3D-printed planes (PLA, LW-PLA, etc.) don't hold up very well to crashes.
@@marc_frank I have built two Soarkraft planes so far. A Pika V-tail out of pre-foamed LW-PLA lightweight version with the MH32 wing, and a Juicy with the RG15 wing with the standard horizontal and vertical stabilizers made out of PLA Plus. Both flew well. The lightweight version was noticeably lighter and the lift took it up like an elevator but it's definitely not as durable. I like this plane! It turns on a dime and is very fast with very little drag. I am currently on another build which is a 2m slope plane with an RG15 airfoil called the "Naughty". I am in the final stages of the build. The Naughty seemed like a lot more work, probably because it was bigger and had more parts. The instructions for the Naughty weren't as good as SoarKraft's instructions and I had to fill in the blanks on a few things and made a few mistakes during the build. The Naughty design uses MPX connectors and magnets to enable the wings to be connected to the fuselage wing saddle without having to connect servo wires, which should be pretty cool.
Like it, what a gorgeous recording- take care-=))
wow!!!!!!!!!!!!!!!!!1
Holy cow! Where does all that lift come from? I think you've found an anomaly location! Very nice!
Amazing plane, nice flight, thanks for sharing
Sehr schön, das Ende war doch nur eine schnelle Landung 😜👍
Looks pretty chilled.
That flying up through the foliage is very cool. I would almost get a DJI system just to be able to do that :)
it was fun, but has risks :) my frame broke in the end will have to do some redesigning
Hi , Can you share more details of the build?
wing: root chord: 150mm tip chord: 125mm airfoil: maybe GOE240 half span: 625mm fuselage: 1.5mm balsa box 6mm carbon tube electronics: 6mm low voltage servos embeded in the v tail diatone 1505 3800kv gemfan 7035 prop AOERC RX142-E receiver with brushless ESC 1x 18650 battery
Very nice.
Nice 👍
Super ich bin gerade dabei einen zu bauen, hast du das Profil von SpeedsterDen verwendet?
ja, hab ich das PW51 und PW2019 3m sollen aber auch ganz gut gehen (nicht als Strak, eins von beiden, durchgehend) ohne scharfe Vorderkante ist er vielleicht ein bisschen robuster wenn der wirklich leicht werden soll, muss auch die Endleiste sehr leicht gebaut werden, genau wie das Leitwerk wenn man normale Ruderhörner und Balsa für die Klappen nimmt, muss man vorne ~100g einbauen, damit der Schwerpunkt stimmt Johan Bergkvist hat ein sehr gutes Bauvideo gemacht
Super
:)
Which transmitter did you use?
it was the flysky fs-i6, now i have the radiomaster tx16s, it's much better
Wow!!!!!!!!!!!!!!!!!!!!!!!!
Nice bro! +like
ABSOLUTELY KILLER FLIGHT MATE KEEP RIPPING BUDDY I'M SUBBING YOU! 😍😍😍😍😍😍
Needs more motor protection! Maybe have the carbon rods extend through the aluminum endpieces?
Nice mate sub&liked - greetings team #bckflp
Homeoffice gut genutzt! ;) Klasse geworden!
hehe ja, stimmt sogar danke :)
Nice Job! ;)
Hi Marc, It is not the world best slope you have there with houses and trees in front of it. But better than nothing :)
no, not the best :) i found two other better ones, but they are further away
best flight starts at 10:23
Sehr nice
Nice Design. Remember the lipostrap :)
it should fit through the middle in either direction :)
Have you tried slope soaring with flight controller yet?
that would be interesting, but very few gyros work with flying wings, plus it would be heavier
Beautiful frames ... how much would the machining cost on the aluminum ?
Beautiful frame. I saw your comment on Wild willy's video.
Oh Cool !
Damn! Impressive!
7:48 ~54g