Video

Very nice job and video editing. What model and year is red car? Gary

It looks so nice 👍

The manual says that a 3" flat surface, at a minimum, is required. It appears as though this would work fine if it's actually less than 3", as long as there's a gap on either side right?

Didnt even see where you put the jigsaw piece.

Looks amazing 👏 I'm looking for a close up on the middle is that concrete drilling into the ground? What is that piece called ? How deep is that? What hardware is that called please

Not a very good video, didn't show us the hinges or the front of the gates, WTF??

Great benefit for growing thick beard is your face wrinkles double chin is covered. Every day when you shave your skin becomes very hard when you stop shaving skin becomes softer. When I used to shave my age looked older now I have grown thicker beard people judge my age far more younger than my actual age that’s because double chin and other lines are covered with thick beard

Does the paste come in a different color

That's a really good job. Looks great. Would be so good to have a parts list and instructions to help someone who's never done a fence before. Everything is so darn expensive to pay. In SoCal they want $450 labor just to install two ceiling fans. Without running any switches. Crazy

The beard suits you brother, I’m on my 7th month currently and am seeing big changes now

Thank you! I needed this

What did you use on the outside of the gate as far as latch is concerned

Dont know if you mentioned it, but what was the size of this door?

Crazy density, crazy steady growth. What a beard

would this plan work for a 20' gap?

😆 🤣 😂 😹 😆 Please show us a new picture

I lay brick for 40 year and that's the first time ever heard somebody charging $1,000 where I come from Best playing around $300 buck

Did the length of the door knob work or did you offset the depth so both ends met

0:48 it’s so pretty how can you say big and ugly?

Thank you!!!

Can you instal a remote control opener to this type of gate?

Nice job brotha

What brands name adhesives should be use for this type of shelves?

i appreciate your service , i need to start making videos as well.

Thank you for this video. Any idea on how long it "should" take to install?

What’s type of lumber did you use?

Hey great video! Love the process and thorough explanation. I have a similar gate built a few years ago and it's leaning a bit these days due to the weight. I've added a gate wheel for support, I'm curious if yours is still holding up fine since you created this video ?... Also are you located in WA state? The houses look very similar to mine. Cheers!

What kind of gate hardware. Link? @JoeMcCoskey

Just a quick tip. If you can't get the drums out hit it on the side with a hammer. It's a lot easier than hitting it on the back. Great video 💪

thanks im removing an old brick mailbox that looks similar and wasnt sure where to start. we'll see if the center is filled like yours

Gates look good. But I have never heard a more confusing explanation of tension versus compression bracing.

Where the link to the hinges?

Thanks for the video! How long did it take to complete the project? Can you paint the cap?

How the fuck you make a video and don’t say what size nuts are that’s the whole fucking point of watching the video

Looked way better puffy!

Thx for the video!

I just installed mine today. 85"H on a shower, no tub. The factory instructions are arleight, but you still need to use your nugget and common sense as they are not perfect. Kohler says to install the bottom threshold 1/8" away from the front edge. While it might work in some situations, it didn't in mine as I would end up with the mounting screws in the literal edge of the drywall of the side walls. I used the bottom threshold with the door guide to position the assembly in the middle so that the edge supports were being secured to the studs. That being said, everything else went really smoothly. Big shout out to my 16-years-old son Max for landing his muscle with the very heavy glass panes.

Looked like it had sagged by the time you fixed the pickets on

Does that work in winter climates where ground is frozen

Should have continued the lower brace up to the top corner mate.

Nice looking sturdy gate. Well done.

Next time: treat the wood with oil or grease for mold release and if you can, make it with a slight taper narrow end deep in wide end at the top.

What type of waterproof construction adhesive did you use? Still holding well? Thanks for the video!

Only problem is you opening the gates. No room to swing doors!

Amazing beard dude!

what are the two pieces on top of the t joints in the final shot? Mini expansion tanks? Copper pressure relief valves?

Great moustache too!

thnku, great video

Time for a beard video?

Yeah grew very well but how did you menage to grow every color of hair known to men 🤣 Looks cool