Video

I had the Evo Clamp 710501, which is little different than this video. It was a struggle, but I finally removed the metal clamps from the feet and recorded a short video here. The technique is a little different and not 100% intuitive: czcams.com/users/shortsXo_PKQY8zY8?si=-jr035JokwuPW-jY

Hi did you end up puttimg these in your car? Interested to see dyno result amd hoe you like them!

It's crazy how you can pretty much order a WHOLE NEW skyline straight from Nissan, or Nismo 30 years later

thanks a lot

Looks good

Wish my car came with the speaker grills. Mine had some blown out 3 way speakers pods and it was starting to crack. Ended up remaking it with some tempered hardboard and speaker carpet.

Why I subbed 🔥

Hell yeah

I'd never seen the air purifier. Those old Skyline options were neat

My old smoke detectors have black , white and yellow wires. Can I wire in the red on my new detectors with the yellow wire? House built in 1994 California

Get an extension cord holder. Or wrap it around your elbow and shoulder. And then connect the ends together at the end in the the loop to keep together

That’s a pressure washer not a power washer

50:1 pre mix fuel followed instructions on how to start and still won't start.... will be taking it back tomorrow

TIM from Canada does this attachment? I just bought it does this fit every small pressure washer?…

nice video, they don't sell these in Canada so I'm planning a drive over the border to grab some of these lol

I went to lexus dealership here in NY and they're charging $250 for each side. Thanks for the video. My car has now 90k miles on it should i change the transmission oil???

Be careful using these - if the head of the screw of the puller is off any it can cause your bolt to mushroom which means you can't get the nut on or off which makes for a real risky drive to the mechanic with your tail between your legs. Working on a 2015 Nissan Altima and this was a miss not a hit as far as tools go. (EDIT) - Turns out Auto Zone had a "Ball Joint Separator 7/8" by OEM Tools" as a loaner. You pay them $35, you use it, you return it, you get the $35 back on the card you used. Easy as all hell threw a 15/16" socket on top to turn it popped off like a champagne cork.

Are Miter blades and Circular saw blades interchangeable?

What make/model is your watch bud?

Mine had 4 wires , black, white , brown and green or blue

Which mirrors are these? Where can I find them?

Great vid. am searching for this type of vid for the R33 GTR VSPEC, but very much enjoyed this one.

Hey Platoon! Just kicking off my project. Your videos have been great. Quick question, when you build out the rough frame for the doors, do you restart the 16” on center or is it simply carried through the framing without having an impact as if it wasn’t there?

Dumb question: Can you rip the tile off of that mesh without damaging it? How hard is it stuck on there?

I didn’t understand how you measured the nevel post, and how you did the cut exactly. Btw it’s a good video. Thank you very much🙏

Many thanks for this video. Not being a recessed lighting expert, the thing that you skipped is how to disconnect and reconnect the actual light. Any hints on that without having to go up into the attic?

If you are in the state of California, Florida, and Texas. And you have at least one gas Appliance. You are required to have carbon monoxide detectors as well. This law is only in California, Florida, and Texas. But it is highly recommended that everybody gets carbon monoxide detectors regardless. If they haveat least one gas Appliance. And they do make smoke detectors with carbon monoxide detectors built in. My recommendation is buy enough smoke/carbon monoxide combination detectors for your whole entire house. Carbon monoxide is a odorless deadly gas that can kill you. And carbon monoxide detector should be taking it to consideration due to the carbon monoxide gases are odorless.

What does this have anything to do with a GTR though? I follow because of GTR content.

I have a 2019 GX and I’m going to be doing all my fluid changes myself when you jacked up the rear did you do it from the differential the rear differential? Is it strong enough to be jacked up from that point if that is the case?

Thanks helpful video! The shop thought my reservoir was clogged😂

AMAZING video ty

Great video!

I really like that you not only showed us where the bolts are but also told us which size wrench or socket to use so that we can grab only those sizes instead of whole SAE/METRIC wrench or socket kit. Great video and instructions.

Thank you

Dropping mine soon because of an apparent leak that I can't seem to find. Hopefully It's repairable & I don't have to replace the whole thing 🥴

Missed a gilden opportunity to scrape all that grass and mid that collects on the deck and sharpen the blades. Very important every year for health of the mower. Also warm the oil up first for it's thinner. Just a a couple tips

Awesome! Do you have part numbers for the inner and outer ball joints?

For the first 10 seconds I was like “Pedro Pascal does reno videos on YT??” This is the way…

Very simple and honest tutorial thanks I'll get er done

You look like Pedro Pascal’s pastier cousin that works in an IT dept

The correct oil filter is the yzza3. Doesn't come with the useless drain tool and small o-ring. Those are for the GR series of engines, not UR.

Fantastic video mate, by the time you’re reading this… I’m halfway through uninstalling mine😅

Living dangerously with those ramps on back and front with no chocks

What if those bolt holes are stripped?

I wish the Chinese would have made dip switches on my remote but I don't have any dip switches and I took it apart and there's no dip switches.

Did you do it cold or hot? I didn't see you measuring how much came out to rwfill the exact amount?

Can you confirm 18x9.5 et12 and 265/35 tires will clear front fender using this camber arm?

Getting rid of the old connector was tripping me up- thanks for including the how to! This was perfect

My car car new turbos new intercooler new charge pipe and vanos solenoids plus boost solenoids could it be tmap sensor or vacuum lines I’m at 103k miles

Doesn't the clamps scratch the painting?