Video

Would replacing the blower motor help with the mildew/mold smell? Once out ima spray with a chemical to eliminate the mildew and mold smell?!?!???

Why is their not a video on 2007 G35 installation on Left rear window

Useless video bru

Thank you

This video needs 1 million likes right now. Saved my bacon right before a downpour.

Did you use a mallet to nudge the window in place? How much effort did it take to push the window into the corner?

The secret must be which end of the new window to insert into the opening. Does anyone have any insight?

3:05 is where vid starts

This doesnt show any of the process. So you have to have the window down when you do this window replacement?

This is really hard to follow

Thank you! That's awesome! That was the exact same issue I had. It now works perfectly!

I have a 95 Toyota Tacoma's with a 60/40 seat Would you be willing to trade it for your bucket to seat ?

If going a video do it complete and show others you talk to much bs

I just did exactly what you did and it worked! It was plugged with 23 years of crap. I taped a small chunk of hose on my shopvac to get in there better. Anyway great video, thanks.

Where is the filter?

Nice

Yo I did all that and replaced every piece of electronics and it doesn't even blow enough to defrost my windshield. In the summer my fuse blew. (The air no matter the temp was CRAZY GOOD FLOW!) Took a week to get everything done and took my dash apart and my evaporator was spotless. I cleaned it anyways with water and cleaner. Didn't change anything. Took it to a shop and they want to charge me to replace a perfect evaporator core when literally weeks ago it was blowing intense. Am I possibly missing something. I'm thinking maybe they installed a shitty ass motor

Hey Johne ?

What did you do with the drain nozzle ? Did you cap it off . Did it even need to be used I'm stuck at this point . So from the looks of it the only ones that have to be connected is supply,return and roll over vent tube?

I'm going to be starting on a project on a 1988 Dodge Ram d250 rwd. It's been sitting in my backyard since 2017

U saved me a whole lotta time! Thanks, This is the same car I got

No help in this video

Thanx for sharig wish you had a better camera but u explained very well. İ have a question ... on the other side of the pipe.. on driver side there is a box wich has a letter a/c B/B and s letters. What those are means ? Mine on S letter vacum sucking line has no pipe ? What can i do about it

Good video John

Since your video was so useless and defective I'll help your viewers by letting them know that you should always change the o-rings on all the connections. And the next time you do a video try changing the tire on a bicycle because this was pretty stupid. You didn't show anything. Next time tell us what crack smoking

Can you do quick video how to remove the 3rd row or how it's done thank you

Did you put direct 12v to the new pump before you put it back in the tank to make sure it worked? I just got a brand new pump and put 12v directly from battery and it just clicks, no spinning of pump. Wondering if I got a bad pump right out of the box or do these pumps need to be submersed in order for free movement of pump mechanism?

Appreciate the video, not that many videos out there with these gen one tacomas. Mine was dirty too, normal for +20 year old trucks.

You say too much but do nothing.

REALLY BAD SUCKS

Starter fluid no worky good on this. I have one. (5.9)

For the speedometer to work goto the abs module harness and look for a small red wire with black line and check for damage. That fixed mine.

How did you align the motor the 4 little bolts ! 10mm

WHAT IN THE WORLD OF MENTAL HEALTH IS GOING ON HERE.

Did you have to remove the entire heater box from the vehicle, or did you just pop the top off?

where it the evaporator temp sensor in there John subbed paw paw

U didn't SHOW anything Geez

Thanks guy, you nailed it! I went to AutoZone and picked up a Dorman universal vacuum connector kit, for $5 and found one that fit both ends just right and fixed it in the parking lot. Now, my AC is blowing cold thru the main vents.

My 2004 ses floors vents won't work lol the defrost and standard air vents work fine though

Cannot see what you're doing..can you pleas make another vid with better lighting

I have same problem with mine now thank you for your video I will definitely try this now

Horrible video!! You were supposed to fix the speedometer we don’t know if you did that or not.

So did you get the speedo to work or not?

I know you put this up a few years ago, but you nailed my problem with my a\c!! Thank you for sharing, it saved me time and money.

Omg thank you for this video! Many thanks!

what year is yours,because mine it 2002 and the interior is different 2001-2003

Why did you buy all 4? Not likely ar all that four sensors went out. Try scanning abs with a scanner and look at data. The one that shows no data driving down the road is the bad one. No way all four go bad like that. Waste of money and time... ahh... do it yourself’rs...

Hey I'm just curious about something...is your heater core laying in there on an angle? The reason I asked that is because I am going to attempt to flush my heater core this weekend. I was hoping you can tell me whether it's easier to get those clamps from under the hood or is it easier to do it floor underneath?

Unfortunately my recirculate mechanism took a dive in the upper right corner between evap box firewall, its huge and wedged in there at an angle. I have done the heater cores before on gen4. My question is this...if you remove the upper right bracket and the middle bracket bolt will there be enough play on the black box downward to put that mechanism in or do you think the inlet/outlets through firewall will restrict it? I really wish i could find a process showing the box removal before I venture into it...any advice is appreciated.

Thanks!