Video

Just a heads up for anyone doing this, make sure you level out your phone because of the new camera bumps. I did this on my OnePlus 12 and forgot about the big camera bump unleveling the glue but I managed to save it by plugging in my charger to the phone and using a small screwdriver to lift up from the port.

I remember having the OnePlus 7 pro. I miss that phone so much with its truly full display.

ribet setan

Put on 20 ultra follow this tip but failed.. glue all over phone and screen.. wasted money

Bąbelki zostały na krawędziach , proszę się nauczyć naklejać szkła uv :)

Bullshit glass fingerprint wont work 😂 yep bullshit glass and to remove it is an hell

наклеил с пузырями, и прячет. Но во время блика было видно все косяки. ужасно. позорище.

Does the fingerprint work on it?

Unfortunately did not work for me.. the bubbles came up as soon as the glass touched the blob.. happy to see others got it right..

Вообщем, нужно быть осторожным. Заклеить все отверстия и делать всё осторожно. У меня ктстати клей не протек за пределы стекла нигде. Ну и поверхность должна быть максимально ровная иначе капля клея стечем в сторону.

Is it (uv liquid) safe for the screen?

I can't recommend this product application is a fairly complex chance for bubbles is higher than expected removing them is nearly impossible ended up throwing it away and washing my phone under the sink because the earpiece was full of liquid after trying to remove the bubbles under screen protector not on edges

This is a gamble. Followed the video in detail. Drop liquid went on the phone without a problem. Placed the glass and immediately a big bubble in the center! Not recoverable. Had to remove the glass and clean the phone. Worthless!

All the glues ended up on my clothes and on my desk because of the camera pop up on my 8 pro is too high. I put the glass on the phone with small amounth of glue that I rescued, but with full of bubbles. :( this method is risky with many of problems. Tomorrow I will buy another type of glass. I`m little bit confused.

Are these case compatible?

Hi, my Nillkin DS+ max came with both the frame and 2 Location stickers, I am confused whether to use both or just go with the frame because it's more precise? Thank you!

Do not buy this for the One Plus 9 Pro! It does not have enough liquid to cover the entire screen so it is unusable

BEWARE! The oneplus 9 (pro) can't lay flat on the table because of the camera bump! You need something to prup up the other side or the glue will just slide off.

Please dont buy it. Having the worst experience with it. I applied it from a shopkeeper without any bubbles. But because of its black border you wont be able to enjoy gestures much as they miss a lot. The black border covers the sensors present on top of mobile with camera. Which causes this issue

Shown VERY badly. I would have been better off not finding this video. 😕

Thanks for the tutorial, I've done mine using this tutorial video, and its all good! perfect and no bubbles!

ഇത് ഏത് കടയിൽ കിട്ടും എന്താ അതിൻറെ വില പറഞ്ഞു തരുമോ വേഗം കമൻറ്

I use it for my oneplus 8 pro. It is perfect!! There are no bubbles its like the white stone dome glass but its more cheaper. Its secret: you have to use better uv lamp (I use my girlfriend's nail lamp) and you have to cure it during 20 sec and after 2x 1 minutes!! If you use the original uv like here, I think it wont be good.

Thanks mate... Your video helped me a lot! Ignore the haters....

That didn't work at all. The screen protector didn't even hold on to the display. There was always air coming in from somewhere. Now I removed the screen protector and got bubbles all over my display. I hope I can get them away otherwise this f*cked up my screen...

Used up both of the screen protectors, both times the last step of removing the protective layer f*cked up the screen protector. The protective layer simply sticks to strong to the screen protector and rips it nearly all the way off. Second time i tried to smooth the screen protector out with the application card, and now all over my screen I see bubbles. I'll wait to see what it does in a couple of days, but I'm afraid I will be ordering another screen protector very soon.

i burned the uv liquid ON TOP OF THE SCREEN. THIS SUCKS!

I accidently made it worse. There is uv liquid on the top fo the screen and air bubbles inside

Great, now show us how to remove it.

i got the same glass but for oneplus 8 im not able to get rid of bottom left corner and bottom right corner glue out. what should i do? can someone help me? i can send you pics of how it looks.

Delivery available in India?

Nice video ☺️☺️

Can someone tell me, if the fingerprint sensor works or not with this glass?

❤️

Thanks for vedio

Thanks for

No one buys this phone i did lose 360$ because it is the worst phone ever and the battery will not last more than 6 hours continuous in addition to changing colors in the screen and also the screen the worst screens found in this category and the biggest problem disconnecting in the wifi connection. It's not worth it, and there's no guarantee from the bad company. if u by any site they give it by them store only

There was no need to pull that skin away

Btw nice guide👍

You really need to be extra careful to apply this tempered glass..one mistake ruin everything..

Awesome! Works perfectly with my phone. Thanks for the tutorial 🙏

I install mine. Works fine. No bubbles. Overspill from the glue can be removed before using the uv light. Fingerprint is working just as good as before. 😊 I'm a happy customer.

This one or nilkin dx which one is better?

Veri nice

Is it compatible with ringke or spigen cases ?

Thanks, easy and quick!

Thanks for sharing, very helpful!

Dont buy this piece of shit. I bought it to hide scratches. It does hide scratches but its very easy to fuck up everything for someone who does it for the first time and the adhiseve is extemely difficult to remove.

I have some small scratches on my phone screen. The glue will cover them ? I'm wondering or can get some bubbles because of them

I thought this would be hard but turned out its actually simple to install. I used the same tutorial for a Samsung S20 Ultra. Be really carefully with the sticker, there is way too much glue and it's very posible that might get into the speaker. If it does its actually really easy to remove it with some alcohol or hand sanitizer as long as your phone is waterproof.