Video

Hey there! Is it alright if I feature this clip in my upcoming video

As a repair guy I say hell no to these That transmission is like 120 to 150 Plus time energy and you still have a washer thats worn out. Buy a 80 90 series Kenmore direct drive and take this sheet to the dumps

You are a legend DIYer.

Thats not a cut off you idiot.

Nicely done! This is by far the simplest that I've seen!

Looks like fun!!!

Would be a life saver if someone could share next steps for Maytag MVWB766FW1 off balance for any size load but empty. Replaced suspension rods. Leveled front to back side to side. Checked washer plate and tower for soundnesses which was nice and tight. Nothing in between drum and linear. Performs wash cycle and initial low speed spin to drain tub but as soon as it picks up from there bang bang bang off balance and walks. At a loss!? 🤷

How much was the transmission

Bravo Adventure Troop

No need to take that back panel off. I used the closed side of a combo wrench and was able to reach just fine and avoid some disassembly.

Good idea but I see 1 major flaw and that is the bearing housings are made of cast iron

I love the way her ears flop

Scout frog!😂

AHHHH im going to SCREAM nobody has MY switch I've watch every video on the internet looked at every thread and yours was the CLOSEST to mine but my motherboard is ATTACHED to the buttons from the inside. So when your whole motherboard just comes out the bottom mine stays up against the buttons from the inside. Nothing will get it loose and I don't know how to pop the buttons off without breaking them :(

❤❤❤❤❤❤ Very nice

I replaced my rollers without taking the rear panel off. Used a 17mm stubby and some lineman pliers.

19:12

I would have chosen to take advantage of the fact that everything was disassembled and I would have given the inner and metal tub, filter, etc. a very good clean.

Thank You for Sharing this Video. Im Glad Im here.❤️ Hoping to watch more videos from you ☺️ Have a Great Day. Greetings from our Family Kapiso Mo Vlog.. Stay safe and Godbless You Always😇❤️ 4:24

Hi Show Me The Honey Blog May I use this on my channel, full credited of course? Where did this happen ? Thanks

Water down the drain...😢

What... no apps!!😂

Biggest pile of junk ever I've been working on Maytags for 30 years and this is the worst

Where did you get the part at. I have the same exact washer but mine squeals while agitating. I’m assuming it has to be the bearing.

which load cell have you used for this project ?

Does this machine have a drive motor transmission?

That rotational knock will damage your new replacement parts in a short time

I will never buy another Maytag washer mine only lasted 3 years biggest POS ever.

👍👍👍

Thank you

The knocking sounds like the stater motor bolt is a little loose? The "stainless steel" tub looked like it had alot of fabric softener residue. I am convinced that fabric softener is what causes alot of gunk buildup and seal failures. These are not the worst washers. There are plenty of Samsung,LG, and GE that take that place. People overload these washers that can not handle it. Speed Queen is the last of the tank built machines. 5-7 years is the average life of most box store appliances. Most of the time,the load of clothes we are washing costs more than the washer. 🤔

Very helpful thank you!!!

I think I'll keep my old whirlpool from the early 90's.

Thanks for saying misbehaving...so funny

Thank you man, I've been looking for a hopeful fix without spending a bunch of money.

is there a vid on how you made this?

Hi, I enjoyed your video. Can you tell me what you used to clean

Those are super cute

Very well thought out is stainless difficult to weld? I've done lots of mild steel but have never tried stainless. About how much did your materials cost?

You high jacked that honey!😅

You video does not show how you remove the basket

Are the O-rings/seals available for purchase for this gearbox or similar?

Does the type of gearbox on this washer contain grease? Or some type of oil?

Has anyone tore one of these gearcases down before and tried to replace the bearing?

I used the flat end of my 6 foot post hole digging bar to pound the shaft of the transmission through the bottom of the tub. Worked like magic!

Thanks for making the video, very helpful!

Good video. These Maytag washers are the biggest pieces of garbage ever produced. I think I’ve now had to replace four major components in three years. One of them twice. Also, why they don’t make these parts exposed to water out of stainless to prevent rusting is mind blowing. They’d rather spend the money tricking consumers into thinking it’s a good product with their Made in the USA and 10 Year Warranty stickers.

Great video. Really appreciate the effort you put into it. Allowed for a quick (3 hour) repair today. I had to fight to get the transmission covered by the 10 year warranty. My extended warranty just expired - of course. All I had to pay for - was the gear pulley and the spanner wrench. Thank you!

Give them to me to repurpose into planters, shelves, displays, etc. 😂

Pretty good video! ❤