Video

Old ass video

Hi mate how do I remove the fly wheel? cheers

What to use to get speakers out screw drive or do the snap in

thanks man, u just save my husqy 250 from 2008

Is this a custom build ?

I can't believe you never cleaned it up before installing the other one. And no grease either to prevent further rust

One of my valve caps broke lol barley put gorce on it and it sheered

I have never done something like this, but I'm planning to. My idea is to divide the circumference into equal parts and draw lines from one side to the other thru the center point. Then, determine the diameter of the vinyl or cloth using a compass draw the circle, allowing enough to fold over and then be accurate while cutting the circumference. An then following the lines. Like a clock 12 to 6 and then 3 to 9 and so forth stapling opposites, the folds should the be consistent all the way around the diameter.

Why are you afraid of the word "pliers"? The name of the tool is "needle nose pliers", not a "needle nose".

Thank you. I'm 60, I need a new tube. I think I can do this! Thank you❤

all that mumbo jumbo and did not state a resistance Ohm range for that injector. Although stating most are about the same, he says he has no idea. Wrong, he has a good idea of a range, but not your specific make and model range. Just ballpark it or state the range of your injector, something when doing a how to test using a multimeter.

Thanks for the video.. i was stuck in putting back the spring. It fell off while I was removing the caliper and didn't know where to put. 😊😊

Termador is the REAL DeaL!

My intake valves are always tight even when i back the screw out all the way

What is ur top speed?

10 years later this work bench would cost 200$

Is this thing why I can't start my YZF450 in gear?

Those mounts are garbage. Good luck! Also, your video is way too long. Couldve been 45s long

My bike don’t have a male and female end but it’s also missing a post that would be for it on the coil am guessing idk help

What to do when the form doesnt go off?

My cars battery was measured at 513A on a 830A battery. Thats not a healthy one and need replacement i guess

Where did you find the foot pegs

How big was that piece of vinyl? And was that a 16in round?

6 years later and the cost is now $122.09 retail, dealer cost is $69.20 . nice video

Thanks so much for the video! I learned a few tricks I didn't know that made changing out mine a breeze. Appreciated. God Bless

I’m 51 years old , the 911 was and is my dream car still. I love ❤️ your 911. I still don’t have one 😢 but loved seeing yours . Thanks for sharing

When removing the air in the forks, just install them on the bike and remove the plugs and jump the bike up and down.

Great looking

Hoy many teeth have you sprocket ? 42T ?

Good video...helps a lot!

Can you put this on a 2005 Yamaha 250 F?

Bonsoir super vidéo pouvez vous me donnez la référence de la pièce [ bague en nylon ] .merci beaucoup.

That looks slick 👍

How many volts was the charger?

Thank you so much Sir

I'm not getting any readings on my meter is possible all injectors that bad?

Thanks! I'm glad I finally found your video!

Hi, I bought the 125SE today and exactly same issue - even with my biker boots its very hard to shift it for me as an adult : / I really need to try hard and focus, loosing a lot of moment, and hurting my feet. Certainly not well made. Cant imaging my son being able to shift. Rest of the bike is awesome. I was surprised how well it can handle my 86kgs and how powerful it is.

You lost me at "Porsch" B Bye.

Very good.. thanks Doing 2 stools tomorrow!!

I replaced mine on a MAsh black seven 125 injection but I cannot find the values is should be set the manual I have of my motorbike doesn't say it

Mine leaks oil from behind it. Is oil supposed to be behind it?

Mine is a cheap plastic one, without a rebuild kit, and no book manual. Craftsman sure went even cheaper.

You sound like Jerry from moonshiners

Thank you man 👍👍👍👍

Love that Trans Am in the back!!!!

Good video. God bless you

Buy a European 911 without those horrible American fenders. They ruin the looks

Nice job on the Porsche, great detail correcting the electrics. Yes it's important!! If I was interested in buying the car and opened the door and heard the buzzer, that my friend would seal the deal!!

Wish these were available in Canada...