Video

Nice 👍

White blades look good😊

We fix sh t with tape

I’ve just finished curing one for 4H

How did you install the LED light kit?

Lol , Master Bruce

would you throw the canvas away? and just sheet it

How do you compact?

hey David, what outlet pressure should i be aiming for on a gas valve converted for propane?

Your video just saved me a lot of time, thanks !!

How fast? Looks great btw

Mine is kicking out in the first two seconds and is drawing 35 Amps

swept blades!

Do you ever use both tape and sealant?

My error was 0x050000. Realized I had some tags in the Cmore project that were not in the PLC. Deleting them solved the error. Thank you!

Thank you for this info 👍

I,m think the abaut you ,brother

Good job....🎉

That's pretty wild. 3 years ago I went on a service call, to a 1960s diner that I and two fellow electricians were working on just a couple of days prior replacing the main panelboard. One of the janitors plugged in a floor polisher that went unusually fast and smoked up. Supply was 120/240 3 phase delta, there was also a single phase subpanel feeding the lighting, security system and some of the receptacle loads, and I was rushing because it was close to midnight when we finished and installed the stinger leg on phase B according to the 2020 NEC, without confirming from my partner who removed the old panel which phase the stinger was on, it was originally on phase C, and he didn't confirm with me where I landed it. The security system was unharmed because it had been on phase A, and the lights were F32T8 electronic ballasts that were 120~277V, so they were fine on the 208V stinger, therefore everything was normal when we left, but we definitely should have verified voltages. Oops.

I use both

Tip: You can take it a step farther a rinse the butter in cold water a few times to remove even more of the buttermilk and the butter will last even longer .

Commercial coolers take around 25lbs when topping them off ? I have a coke cooler it holds 16.5 Oz and I topped it off to around 5lbs and it’s cooling should I have added more?

Heh.... Jacket off

I call BS! No new wire or new lug. Electrical tape and wire brushed the lug.

Lucky no fire

Didn’t know lose bolts cause heat like that

How much did the customer pay for that?

Maybe investigate the reason it did that. If you just replace the wire and the lug, would it stand to reason there was a cause?

That's not a repair job It's a service upgrade. It's going to happen again to much load being used. Needing a 200amp

Dang it was red hot 🔥

No torque marks on those lugs, no anti seize, definitely 😁 wasn't inspected it never would have passed.

, pull the blower out, recover the Freon and pull the coil

Thats likely a contributing factor to the failure. Should have been a suction core before that suction bell screen. Its not common to see those screens clogged up like that.

Arc flash causes getting hotter melting aluminum copper

If it gives you the option I would install a main breaker for overcurrent protection. That will help prevent Is that from happening

It doesn't really get much closer than that.

Burning down the house😲

I wanna see you use it on the air duct connects

Those damn building regulations. And god damn electrical inspections.. fxcking electrical saftey. Health and safety bollocks... is what everyone says until this happens....

Who is the DODOs that say a Trane is not good. They probably don't know how to install or repair them properly. I've never seen a Trane break down including mine which has to be 35 years old. Now that I know a Mitsubishi is Trane a Heatpump will be by next upgrade.

I’ve seen a very loose spade on a meter get red hot too….the whole meter base had to be changed out….

Lucky it didn't destroy the buss bar.

I’ve seen that before, it was after hurricane Laura and the lineman swapped the neutral and one of the hots on my brother in laws house. He called me and said man my fans are all running stupid fast, my A/C is blasting air out the vents…. “TURN YOUR MAIN OFF ILL BE RIGHT THERE!” That house would’ve burned down

That's all set up and still get plc-26 error

Traducir en español

Do you have a video of how you guys replaced the wire and the lug that would be sweet to see!

❤❤❤❤

Code is over rated

Where can I order a back fill blade ?

When checking we can use either color of lead. Ex: I watch other video, some guys use red for common and black for Fan.