Video

Have a DU201 and my helper is 75 years old and she doesn't like to get dirty. You are a lucky guy. Teach him well.

Should the fan blade spin freely while the pump is still connected?

Thanks for your great video 👌

Do the F turbinator heads always come off the nozzle assembly so easily? Loosen one screw and give it a wiggle and a pull? Are they all held on by friction alone?

Your helper is awesome. Thank you. Great content. Appreciate you sharing your expertise.

If I change the motherboard does it need programming ?

I have the same attachment foe my ash vac i use on my pellet stove except the bristles are a wire brush instead of plastic. Should work mint for doing my furnace. Isn't there a few other things like adjusting the fuel ratio and checking the co2 being released or something? And also ik you gotta use Chimney Sealant stuff, kinda like mortar around where the exhaust flue meets the actual chimney, also how frequently do i need to clean my actual chimney for my furnace? Idk if ive ever seen my plumber do that, he has however cleaned the exhaust flue that goes from the furnace to the chimney. And last question, also how do you adjust the oxygen ratio and air intake vent? Is there anything you even have to do there and if so how frequently?

3 years later. What an excellent informative video. Thanks from the UK.

This a great video for that 'headache' thing. Thank you.

Hi what type of screws holds the motorized valve to the frame i tried a philips but i cannot get really tight.

What happened to the programming link?

What is the large piece that you are working on that it's connected to called? Just called an oil burner?

2 questions: 1. Why not use the common wire? 2. Why not mount the metal box cover to the box first, then the thermostat?

can i just leave zone valve head off and open up with that little handle so its getting hot water all the time when the other two zones call for heat?

Hi I got a question for you I have smoke coming out of the oil burner and I have oil leaking under de oil burner as well is that has to be with the oil pump or I will have to replace the entire oil burner.

TRULY , a fantastic explanation about a zone valve. Excellent.

Thanks for the detailed video.....I just purchased some Beckett electrodes and they along with the old set have what looks like a butt connector to attach the length electrodes ends to match the others. The instructions don't say to crimp them or anything

What spray were you using to clean it ?

Thanks for this video! My problem is I cant not move that level freely and it seems like stuck in the middle while I can still feel the motor is hot. What do you think could cause the problem? Do I have to call the strata to replace the whole thing? Thanks

A question for you about bearing noise. I have a two-year-old furnace, and I'm hearing some pretty bad-bearing noise coming from around the fuel pump. At this point it's intermittent. I thought originally it was coming from the blower motor but upon closer examination, it's coming from around the Motor or the fuel pump. I'm assuming there are several bearings in and around the motor and fuel pump. Which do you think would be most likely to fail after just a couple of years? I've actually had furnaces 10 plus years old and never had bearing issues before, but this noise Is fairly loud and can be heard from 10 feet away.

Hi, how would you suggest detecting location of heating pipe for baseboard water heater behind wall? Former owners severed the pipe in the boiler room for the basement. Thanks!

Are you adding a fill gauge

I don’t miss these times of having to wear a mask in customer homes even though I always took mine off on e the customer left me alone in their boiler room. Anyway I stopped using pipe dope and know use Blue Monster anti-seize that’s rated for solvents and all fuels and I’ve had great success with it.

Does the higher voltage of the igniter improve combustion? Does it tax the ceramic insulation of the electrodes?

My furnace quit today tried new filter. Ended up taking off b2va suntec pump and the pump shaft just came out of the pump thats not supposed to happen right. Any input appreciated.

Hi Mister Great video. I like to know what cause bleeding every 3 days? I replaced my single stage. Thank you

Hi there great video . I have a question because it getting cold and my furnace is not working. I have air comming out of the inlet filter on the side of the blow motor . Does this mean the motor is running backwards? The air is comming out of the filter where you adjust the air flow going into the burner head it that makes sense . My burner is a Beckett . I furnace runs but not well . I have changed everything from the control unit , nozzle,new igniter box. I thought the air was supposed to go into the burner head from the side where the adjuster ring goes. Should I change the direction of the blower motor ?

I'm curious if have 5 zones everything in 4 work fine the 5th is my garage it is always calling for heat even when the tstat is off. If the zone valve is set to auto but I'm curious if it is somehow stuck to open would that be why the zone is always calling for heat?

hi, is this installation is for heater only

Did you have to drain whole boiler system line prior to cutting copper radiator??

Very helpful video, thank you! Like another viewer, I now think I can fix my defective valve myself. ✅☺️

this video was PERFECT for helping me troubleshoot my honeywell zone valve problem, also gave me the confidence to do it myself. just got everything put together and tested and back to normal operations in plenty of time for winter. thanks for making this video!

It's been a couple years since I did this, but it would have been nice if they had put a note/warning with the pump that it was full of oil. Made a bit of a mess. I also had to put the pump in a vise and use a breaker bar to get the plug out for the fuel line. Made in France I recall. Has run like silk since putting the CleanCut pump with solenoid to replace the previous.

Great job if you don’t mind me asking how long did it take you to disassemble , clean and reassemble?

Are you in Anchorage? I have six of these at my apartment building, and I've had to have 14 motors replaced in 2 years. Either failure to open or failure to close. The plumber only hooks up the two yellow wires, leaves the red ones disconnected. Could that cause problems?

Thank you

How many years of training does it take to be certified?

I need help with mine that looks like this! I’m so sick of hearing I need a whole new boiler system because no one can find this pump

Could you have done that repair with a ProPress?

Satisfying!

Why is it just for hot water could we not put this on a cold water system??

Does isolating the valve by turning off supply and return eliminate the system pressure when you pull off the old plate? Thanks for the video

As soon as I turn on the boiler there is a call for heat, even though the heating is off at the program box. The hot water works normally just the heating is messed up. Do u think just replacing the metal box would work to fix the heat so it could be called when needed?

Is there a way I can get a stuck open valve manually closed until I get a new one?

Great! very helpful

Very informative. Thank you.

Ive been having trouble with my bekett burner. Ive trouble shooted everything i could think of and cant figure out the issue. My blower fan is not kicking on when i turn on the heat switch. It will kinda of turn on but get stuck then it trips my breaker. Do you think it could possibly be the fuel pump? Or something electrical? When i trouble shoot the motor blower alone without being assembled it works normal but when i place it into the shaft it looks like it gets stuck. Id appreciate the help. Thanks!

I have just replaced my Honeywell motor head. I must have an older style as there are no screws holding it to the valve body. It is only held on with a wire clip. The issue I’m having is that when the thermostat calls for heat the motor head comes disengaged and does not open the valve. If i put pressure on the motor head towards the valve body it will engage properly.

thank you !