Video

Nice job, thanks!

Like there no repairs on pull cord replacement 😅😊

I just got a 2014 yamaha Zuma 50F for free in mint condition. Only has 5k miles on it. When I try and start it, the starter seems to be struggling to move. Just ordered a new one and hoping that solves the issue. What would you recommend doing ?

Thank you sir for the very informative video. I will be performing the maintanance now on my 2000 Grizzly 600. I sure appreciate it!!

Thank you for the video. I feel confident I can replace it myself. I sure appreciate the video and your time.

Nice job

Great video , did it last the rest of the life of the truck ?

To all of those eastern europeans and asians who take a pile of rusty iron and spend twenty minutes performing obscure machinations before revealing that their 'amazing' invention is just another wire twister or metal bender... WATCH AND TAKE NOTE OF HOW NOT TO WASTE PEOPLE'S TIME. Nicely done sir. Liked. Subscribed.

My guides are rusted through. Going to buy new guides and replace following this video. Thank you very much for this!

Do not use a ratchet to remove the pulley

I use a hand belt sander with a Fine aluminum oxide belt diablo from Home de pot to sharpen my blade and it Works Slick!

Donde lo comprastes

Thanks for the video!

thanks!

thanks for the video. I found it very helpful. I was able to fix my handle myself with your helpful video

Super helpful thanks

Cool learning video!

My speedometer light and the headlights both don’t work, they went out at the same time. Any idea on what it could be.

You should always take filler plug out before pulling rear. Because if it rusted solid you’re not putting new rear fluid back in. I had that happen on my Ranger and had to buy aftermarket rear cover with filler on rear. I knew this before I did fluid change because the axle filler was frozen.

I appreciate videos from people like you. It's very valuable to have a good idea of things to expect with every fix-it we all encounter, thank you sir

What if my window wont roll down at all? Can i still replace the track? Mine is rusted out.

This is a great video. I have watched it several times and am now putting the I for action to use in changing the bearings on my sharpeners. Thank you for taking the time to produce this video for us Fleming Gray swing arm users.

From what I gathered it's the 1000watt rear hub or any hub electrical drive motor that should have torque arm's , not a 750watt motor as this thing has, your far from wrecking this thing with only a claimed 80nm of max torque. But go ahead and put on said arm l don't care, would be interesting to know how much you stole this thing for from the spoiled brat family that got the punk a car after putting 37k on this thing, there $2700.00+ in Canada, my guess is it went for half that or less.

(Gracias Brother) 🤝 Pienso Hacerle Lo Mismo Ami Honda Pilot 😎👍

I'm picking one up hopefully??

Any vids on a 600 that gets quite hot on the right side. Great vid by the way. Learned a lot!

The upper bushing makes that noise I had to replace my drive grain or shaft just for the upper bushing the next tom I just let it be. 350k mazda b4000 4x4 bought it in 1993 but it's a 1994 model. I told the dealership it was my upper bushing by they said it was my leaf springs so they gave me new ones and then realised I was correct. Letting out the couch and transferring power to drive shaft puts pressure on upper bushing. Just drive it easy and don't worry. ONLY under power it clunks . The bearing is fine. I've pulled people out of sand 100s of times in the desert and towed many trailers. After my replacement shaft began doing the same thing I just said it's the nature of the beast and put 200k more miles on it showing no mercy. 🚬 THAT. 🇨🇦 And my fan for my radiator is made in 🇨🇦 it's been cracked for ever but still it does its job. I did have to remove it and clean it to make it efficient because it is heat activated. The mass airflow sensor can be cleaned but mine is needing to be replaced tomorrow. Will do.

Bought Brace/Bracket from where?"

i have question my 2008 zuma 50cc electrical start dont work what could it be. i have fresh new battery and 7 amp fuse. i only heard click from start relay

Take off the shim you don’t need it it’ll make your bike go top speed 40mph

will never understand why people call rot rust lol. the shock tower rotted out didnt rust out.

I would have tried thread tape just to see if it would work because thats a crank shaft replacement . I don't think the thread tape is a full time fix but it would go till the parts come in .

take the seat out and you can get to the starter much better dropping the tier and the exhaust is way to much work to change the starter .

Great video and very informative, thanks. Do you have a list of the tools you had present to complete the fix?

Video was a big help. Mine got messed up from dirt, right side Also.

Hi.Great video. Have YOU CONTROLLED IT FROM THAT SCREEN? THANK YOU. RIDE SAFE.

My Grizzly was missing and I decided to check the valves. I found TDC with the viewing window, took off the valve cover and found them to have a lot of play.(Maybe a 1/4 inch) How can you set the valves with this much play.?

Thanks, it's a big help to know in advance what the job is going to entail.

hey that float pin goes out the other way

Loved the video. Lucky cat. Lucky cat momma. Especially appreciate the “no fancy joinery”, “no fancy tools”, “no annoying music”. Stress free project that can be built by the enthusiastic but not necessarily finishing carpenter. And love - we ain’t building a grand piano!😹

Bend your feeler guage

Great video. My cats would love something like that, I might have found my summer project. Cheers!

Buen video.Lubricastes el taladro.Muchas gracias.

Unfinished

Awesome. Had to chuckle at the tight oil drain plug. Mine is same and I did same thing as you but still won't budge. I'm afraid I might snap something. Thanks for a very clear video.

Buna kilometre nasıl takılıyor

My frame is rusty, can I weld on steel to the frame and bolt my bracket through the new steel?

드라이버 기술이 대단하십니다

Tip for the future when you put the motor together make the screws sung I always oil my fans when I take them apart I collect fans. Sometimes you gotta tap the shaft in order it get the bearings aligned it will spin free and not run slow or it could be dry bearings it will make it last way longer.