Video

My family forgot the code for our kiddle safe 11 years ago they would pay whoever mangaged to open it 50$. I thank you very much for making this video, it was a great help😊

What about in between the annual service? We had ours run for 6 days after Beryl.

Battery is critical, often overlooked. Before doing anything, check the trickle voltage to the battery, that's what keeps it charged between runs. Should be over 13v generally. If not, battery isn't getting charged to start the unit when needed. I've changed the standard clamp leads to marine grade terminals, cables are attached with lug ends, then sprayed with NOCO anti corrosion spray. When the unit is running, battery voltage should be over 14v, and yes battery should have full cell levels of distilled water. If you disconnect battery, Generac procedure is to remove 7.5 amp fuse at control unit, then disconnect white charge wire above the battery. After reconnecting battery, reconnect charge wire and insert 7.5 amp fuse. Then check all trickle and run voltages. May all sound like overkill, but the worst time to find out battery issues is when you lose primary power......

The corrosion you see on the battery terminal, cost me $300 for a service call to my rental cabin. The Guy cleaned the terminals. That was expensive 10 minutes. I will put in a new AGM Group 35 4year battery, best price Walmart.

Have the exact lock in video. I could not feel jackall pushing the buttons. I read the comments and saw people posting using wd40 on the buttons and they started feeling the push back from the buttons. I can confirm 100% success after working break free oil through the buttons. I let it sit for a few days button side up and was able to get the code. To be clear, I 100% could not feel anything until using the oil.

good video. change the setting on your camera so you are oriented properly. That way you are removing your filter instead of tightening it :)

Great vid! Bambu have lots of documentation but honestly they do a bad job of explaining the simple stuff, like how to pause on a layer by right clicking the slider. I have been wanting to do hueforge prints and now i know how they pause for manual changes.

Hi, our family hub freezer isn't functioning as it should. It is warm inside, the temperature on screen is -19 but the actual temperature inside is about -7.

I have a 2019 RAM and I don't see anything like you're showing

Can’t thank you enough for this video man, thank you so much for taking the trouble to share, I have been pulling my hair out for weeks trying to resolve this. I was just about to give up when I came across this so thanks again from the Emerald Isle 😀

One tip, running the engine up to temperature before draining the oil will help with drain it faster/completely. Good diy video!

Couldn't you have powered the dig quads with the 12 volt power then take 5 volts from it to the relays?

It's great you had a go fixing this old tape machine - Tape Apes will chatter but you are a 'class man' for doing a good job on these difficult machines. Well done sir... 🤓

Didn’t work for me. I can’t get it to do the engineer mode

If you fill the whole plate you can get quite a bit done for a two minute change. Nice!

Hi, I am having an issue with my 1506 that is driving me nuts...do you service the deck or can you recommend someone?? thank you

Thank you, this is the best explanation YOU MUST use something solid to push with. Took less than 3 mins Thank-you

Good stuff thanks for posting.

You showed nothing in terms of the actual replacing.

Thank you King you saved me 🤞🏽

Super helpful. Thank you!

How did you attach it to the soffit ?

have one i will sell you

Genius! Saved my life. Thank you so much.

Whats the name of that tool that goes into the adjustment knob?

Looks a great solution but mine doesn't behave! I don't think my OPEN button slides down as much as yours so all the number buttons are totally resistant to any pressure. Any further ideas please?

Wont work for me. Dont feel sht

who sells the Miracle Paint other than MS, I was wondering if its available locally.

Thank you!!

*promo sm*

I like your video the only problem is that you didn’t tell me how to set the new combo, but that is what I need to do. My lock is brand new but no instructions how to set the combo. This is the closest I got to get any answers. Thank you in advance.

only 2 buttons pushed down? now what??

Excellent video for replacing dial and lock. Thank you.

Need help. I dont feel thebpush back even if I press hard on the buttons. I do feel a couple of numbers but they dont work

The component that fried is a surface mount resistor. It's the same style as the R250 resistor beside it. The value is almost readable through the gray ash. It's the same as a normal through hole resistor just pcb surface mounted. Looks like trace J5-5 got overloaded somehow. 2 resistors right next to each other like that is usually a voltage divider that steps down the voltage but it can only handle a certain amount. Therefore it likely was overvolted somehow and blew the resistor divider. Lightning strike?

Thank you! Worth the time it took me as it contained a key to the front door of our new house 😳😅

Gonna try😢

Yes, definitely.

Hi, did you notice a difference? The engine sound good!

2k subs, 120k views. 😄

I just got a 3.5 inch lift. So I guess I should lower the headlights 4 inches just to be safe. I also feel like it’s not eliminating the asphalt as much after the lift.

What do you do when reset button won’t work?

I have a 6 month old Whjirlpool oven and it doesn't work like that.

Good day Sir 👋 I created a playlist with different preset inside of the playlist I've made but it's not playing or changing preset that is included on the playlist I've made

Is it a secret what caliber ..??

The rifle on a nice lighter surface ( blanket maybe) would enhance the viewers watching experience ...!

The words you used to explain the pressure feedback on the opener slide solved this for me!!! All of the buttons were "tight" but not all of them would push back on the slider when tight.!! Thank you!

Thanks! Replacing mine this weekend and this really helped!

Really? No follow up on if it was enough? Some influencer you turned out to be. Jk thanks for the info

Fixed it!😅